Starrett 5004 Depth Gage Instrukcja Użytkownika Pobierz pdf (Strona 2)

2 3

Operating Instructions

On/Off

AquickpressofeithertheMODEorSETbuttonwillactivethedisplay.Toturnthe

displayoff,pressandholdtheSETbuttonfor2seconds.

Mode Button

This button toggles the display through the selection of a variety of functions.

SET Mode

WhileinthismodeaquickpressoftheSETbuttonwillzerothedisplayorsetittothe

datum value established in the preset mode.

REF Mode

Whileinthismodeaquickpress

oftheSETbuttonwilltogglethe

displaybetweenabsolute(ABS)

andrelative(REL).

AquickpressoftheMODE

button will exit this mode and

displayeitherABSorRELon

the bottom right corner of the

LCDdependingonwhichone

was chosen.

UNIT Mode

The gage can be changed from inch mode to millimeter mode, or the reverse, with one

quickpushoftheSETbutton.

PRE Mode

ApresetnumbercanbeenteredintothedisplaybyfirstpressingtheSETbutton.

Anegative(-)signwillflashtotheleftofthedigits.Toselectthenegativesignpress

theSETButton.

IfapositivevalueisdesiredpresstheMODEbuttonandthenegativesignwill

disappear(nosignsignifiesapositivevalue)andtheleft-mostdigitwillbegintoflash.

ToincrementthenumberpresstheSETbuttonuntilthedesirednumberisachieved.

Then,usetheMODEbuttontomovetheflashingcharactertothenextdigittothe

right. Continue this procedure until the last digit has been selected.

Hold Feature

WhileintheABSmodeavaluecanbeheld(frozen)inthedisplaybypressingthe

SETbutton.AquickpressoftheSETbuttonwillreactivethedisplaywithnolossof

position.

Output

ThistoolcomeswithanOpto-RS232outputportthatallowsdatatransmissiontoa

variety of peripherals by connecting to a Starrett DataSure

Wireless Data Collection

SystemusingaCat.1500-3A-1Nendnode.Connectionthruatraditionalwireisalso

possible.

Print Command

The print command is controlled by the mm/inch button.

Battery Installation

ThecalipercomeswithoneCR20323V

battery installed. To change or install a

new battery refer to Figs. 1 & 2.

First,removetheoutputcover(1)[See

Fig. 1]. Then, remove the battery cover

(2)byslidingitinthedirectionofthe

arrow.

Next,lifttheclearbatteryprotector(3),

oldbattery(4)andbatterygasket(5)out

of the compartment.

Toinstallanewbattery,firstmakesure

thebatterygasketispositionedcorrectlyinthebatterycompartment[SeeFig.2].

(Note:Itisimportantthatthegasketisorientedcorrectlywiththerubberprotrusion

betweenthetwoholesfacingdownward.)Next,placeanewCR2032batteryplus

(+)sideupintothebatterycompartment.Putthe

batteryprotectorbackintopositionontopofthebattery

gasket,againmakingsuretherubbergasketiscorrectly

positioned in the cavity. While lightly pressing down on

thebatteryprotector,slidethebatterycoverbackinto

position over the protector. Finally, insert the output cover

into the output slot located on the top of the cover.

TheLCDnowdisplaysthetwounits-mmandin.Select

thedesiredunitbypressingeithertheMODEbuttonfor

metricmodeortheSETbuttonforinchmode.

Figure 1

Figure 2

1 2

Komentarze do niniejszej Instrukcji

Brak uwag

Starrett 5004 Depth Gage Instrukcja Użytkownika Strona 2

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Urządzenia pomiarowe Starrett 5004 Depth Gage