Starrett SR200 Surface Roughness Tester Instrukcja Użytkownika

SR200 Surface Roughness TesterUser Manual

2.4 SR200 Specifications subject to changeFigure 3a Figure 3b Adjustable Support: This can be clamped at any position on the slide of the m

SR200 Specifications subject to change 2.5in the holder. It is advisable to connect the lead to the display-traverse unit first and then the pick-

2.6 SR200 Specifications subject to changeMounting: On a flat surface the display-traverse unit can be supported on its three feet. If a use

SR200 Specifications subject to change 3.1Chapter 3 Getting Started Battery To insert a battery, open the compartment by sliding the door to the

3.2 SR200 Specifications subject to changeMaking a measurement Note 1: If the pickup has been changed or the instrument is being used for th

SR200 Specifications subject to change 3.3If multiple parameters have been selected they may not fit on the display. To continue viewing the rema

4.1 SR200 Specifications subject to changeChapter 4 Menu Settings The operation of the SR200 is based on making selections from menus presen

SR200 Specifications subject to change 4.2on the screen (see below). Press the SCROLL  key left to right across the columns then press the SELE

4.3 SR200 Specifications subject to changeRange: Allows the user to scroll through the range options. The most common settings are as follo

SR200 Specifications subject to change 4.4EVALUATION LENGTH RANGE UNITS FILTER DUMP MODEAll other settings are carried out via the PC. SPC Mode I

Table Of ContentsChapter 1 Using the SR200 with a PC 3.3 Specification for Data Dump 5.5Introduction to Surface Texture Printing 3.3 Chapter 6 Accesso

4.5 SR200 Specifications subject to changeSelecting OK displays the Select language and select SPC mode screen.Select LanguageSelect SPCmode

SR200 Specifications subject to change 5.1Chapter 5 Making Measurements - Technical Considerations Operating Notes Before measurements are made,

5.2 SR200 Specifications subject to changeCut off A few trial measurements made on different surfaces will soon demonstrate that on some, th

SR200 Specifications subject to change 5.3Measure before print pressing PRINT  key before measurementNo parameter selected pressing PRINT  ke

5.4 SR200 Specifications subject to changeLanguage of printout same as language of displayThe printout heading is shown below:Starrett SR200

SR200 Specifications subject to change 5.5Specification for Data DumpThe following format is used for data dump from SR200 to a PC. Transmission s

6.1 SR200 Specifications subject to changeChapter 6 Accessories Replacement Standard pick-up (SR-112-1503) Details as the standard pick-up,

SR200 Specifications subject to change 6.2Chapter 6 Accessories Replacement Standard pick-up (SR-112-1503) Details as the standard pick-up, (see

Chapter 7 Maintenance Calibration Reference Standard The sensitivity of the instrument is checked with the reference specimen supplied. This comprise

Table Of ContentsChapter 1 Using the SR200 with a PC 3.3 Specification for Data Dump 5.5Introduction to Surface Texture Printing 3.3 Chapter 6 Accesso

1.1 SR200 Specifications subject to changeChapter 1 Introduction to Surface Texture terminology and definitions Surface Texture Definitions Ev

SR200 Specifications subject to change 1.2Note: almost all parameters are defined over one sample length, however in practice more than one sample

1.3 SR200 Specifications subject to changeRmr: Material Ratio is the length of bearing surface (expressed as a percentage of the evaluation

SR200 Specifications subject to change 2.1Chapter 2 Description The SR200 is a portable, self-contained instrument for the measurement of surface

2.2 SR200 Specifications subject to changeTraverse Unit The top panel of the traverse unit carries a membrane type control panel and a liqui

SR200 Specifications subject to change 2.3Pick-up Mounting Components The pick-up is fastened to the drive shaft by the following means: Mounting